Classic Colour Collection

• Easy to apply

• High coverage

• UV and water resistant

• Will not flake or peel

• Contains no biocides or preservatives

• Safe for use on Children’s toys EN71/3 DIN 53160

• Can be used in a wide range of applications

The colours shown above are indicative and are only as accurate as a screen can allow. We always recommend a trial application to ensure you have the right colour before you commit.

Colours shown are indicative and are only as accurate as web displays allow. We always recommend a trial application first to ensure that you have picked the right colour

Suitable for: internal and external use
Recommended timbers: All
Applications: doors, windows, fences, sheds, cladding, tables, kitchen cabinets and flooring (2 coats of hardwax oil recommended if using with a floor).

0.5L covers approximately 12.5m² in one coat or 7.5m² in two coats depending on the timber and method of application*
1L covers approximately 25m² in one coat depending on the timber and method of application*

*Rough sawn timbers will increase consumption by a factor of 2 to 3. It is advisable to sand the timber surface first to create a smoother area to apply to OR speak to one of the Team at Treatex to discuss further options to improve coverage.

Preparation

This product works best on unfinished timber. Previously porous finishes should be thoroughly cleaned or lightly sanded with all flaking and peeling removed before application. Ensure the surface is dry and free from any contaminants. Make sure you buy sufficient product to complete the whole project and mix multiple tins together before use to achieve the same finish.

If you find decay, mould or fungi, this should be treated first with Treatex Preservative. Exterior timbers with high tannin levels should be treated with Treatex Stain Inhibitor. Timber must have a moisture content below 18% and the temperature should be between 8 and 24 degrees celsius during application and drying.

Application

1. Make sure the tin/tins are stirred thoroughly before and during use.

2. Use a brush or roller to evenly apply the Treatex Classic Colour Collection, moving in the same direction as the wood grain. If possible apply the first coat to all sides of the wood before installation, paying particular attention to any end grain. Apply liberally on the end grain to fully seal.

3. After 12 hours of drying, a second coat can be applied. After this coat, leave for approximately 12-24 hours to dry. A third coat may be needed if applying a light colour to dark timber.

Treatex brushes and rollers are available. Wet brushes and rollers can be cleaned with Treatex Thinner or white spirit. Store tins in a cool and frost free environment. Unopened tins will last for five years. Once tins are opened, transfer contents to smaller airtight container. For a different sheen level on internal timbers Treatex Classic Colour Collection can be overcoated with Treatex Hardwax Oil Clear Matt, Satin or Gloss.

Item No. 500 (Cool Cotton), 501 (Bleached Wood,) 502 (Sea Mist), 503 (Old Pewter), 504 (Battleship Grey), 505 (Is This Pink?), 506 (Burgundy Red), 507 (Fresh Lemon), 508 (Sage Green), 509 (Forest Green), 510 (Granny's Bonnet), 511 (Midnight Blue), 512 (Stygian), 513 (Ash Bark Green), 514 (Saddle Brown), 515 (Heather Haze), 516 (Admiralty Grey), 517 (Black), 518 (Terracotta), 519 (Muntjac), 520 (Symphony Blue)
Sizes: 0.5L (d), 1L (e)

• The deck to be treated has to be porous, like softwood and should be weathered, clean and dry. For very old decks clean using Treatex Rejuvenator first.
  

• The deck must be thoroughly dry before treating. Mix 10% of Treatex Thinners with the Classic Colour.
  

• Before application, we strongly recommend a trial area is undertaken.
  

• Apply 2 coats of the classic colour thinly and evenly along the grain allowing 6 – 12 hours between coats.
  

• Although not essential, we recommend the deck is finished with 1 coat of Treatex Exterior oil or Treatex Anti slip decking oil.
  

• Ultimate toughness is achieved after 5 days, however, the deck can be used carefully after 12 hours.

Treatex Classic Colour Collection can be applied to metal objects. 

The object to be painted needs to be dry and free from dust and loose particles. Rust does not need to be removed completely, only loose material with a stiff brush. If the surface is very smooth, provide a light key using 150 grit sand paper or wet and dry paper.

Apply Treatex Classic Colour Collection as per usual but don’t try and apply a thick coat. Allow to dry thoroughly before applying a second coat.

Please follow these instructions in conjunction with the ones on our website and the tin.

Disclaimer: We strongly advise that a test area is applied first to ensure that you are happy with the result and that the metal will accept the finish. We have only tested on a number of metallic garden items and would always air on the side of caution when approaching a major project. Treatex offers no warranty or guarantee when Classic Colour Collection is applied to metal but we will offer our usual high level of guidance and experience if you have any questions.

Thanks to Wharton Lodge Cottages near Ross-On-Wye for these images of their two story garage, It was sanded down and then applied with Treatex Classic Colour Collection Battleship Grey

Thanks to The Roost, Merthyr Tydfil for these images. They Used Classic Colour Sea Mist to treat the interior OSB walls of their Lodges.

Mr Nicholls Sent us this photo after completing a fairly sizeable renovation of his garden. Here’s what he had to say:

”I just want to say thank for you for the paints you guys sold us over the last few months, it was an ongoing garden project in which we used the Classic Colour Paints; Battleship Grey, Midnight Blue and Cool Cotton. The quality of the paint and the weather resistance is second to none, I’ll be using and recommending you in the future. Many thanks.”